ADAS Calibration in Garland, TX
Dallas County · Our shop is in Garland — in-shop and mobile service both available here.
Garland is where our facility is. NOS Diagnostics & Calibrations operates from 3002 Edgewood Dr Ste 7, Garland, TX 75042, which means Garland vehicles can be calibrated indoors on a level floor under controlled lighting — the conditions a static procedure actually requires — or handled with mobile service where the manufacturer procedure allows it.
Our Garland facility — our only physical location
NOS Diagnostics & Calibrations3002 Edgewood Dr, Ste 7Garland, TX 75042
214-991-3740Get directions
In-shop and mobile service in Garland
Because Garland is our base, no travel time is built into a Garland job. Vehicles can be dropped at the Edgewood Dr bay, and qualifying calibrations can instead be performed at a Garland shop's own location. Garland is our only physical location — every other Dallas–Fort Worth city page on this site describes mobile and service-area coverage, not a second facility. Scheduling is arranged directly by phone at 214-991-3740 or through the request form.
Mobile service in Garland covers dynamic calibrations, scans, diagnostics and programming that can be completed at your location. Static procedures that depend on exact target distance, level floor and controlled lighting are performed in the Garland bay rather than approximated on a driveway or a sloped lot.
ADAS Calibration After Windshield Replacement in Garland
Most vehicles with lane departure warning, lane keep assist or automatic emergency braking carry a forward-facing camera mounted to the windshield glass or its bracket. Removing and replacing that glass changes the camera's position and aim, so manufacturers call for a recalibration before the vehicle is returned to the road.
For Garland glass work we perform windshield camera calibration to the published procedure for that exact year, make and model — correct target, correct distance and height, verified ride height and tire pressure, and a dynamic drive cycle where the procedure requires one. The job leaves with documentation showing the system was verified, not just a cleared code.
ADAS Calibration After Collision Repair in Garland
Collision repair disturbs more sensors than most estimates show. A bumper R&I moves front radar and parking sensors, quarter panel work affects blind spot modules, and mirror or grille components carry cameras of their own. Any of those, plus alignment and suspension corrections, put the vehicle back into a calibration requirement.
Garland collision centers can use the Edgewood Dr bay for static work and mobile service for the rest. Every collision job includes a pre-repair scan to record what the vehicle arrived with and a post-repair scan confirming systems are clear afterward.
Forward Camera, Radar and Blind Spot Calibration
Forward-facing camera calibration covers the camera behind the windshield that drives lane departure warning, lane keep assist and automatic emergency braking. It is aimed to the manufacturer's target geometry and then confirmed with live data, because a camera can read fault-free while aiming several degrees off.
Radar calibration covers the front radar behind the grille or bumper that feeds adaptive cruise and collision mitigation, and the rear radar that feeds cross-traffic alert. Blind spot calibration covers the rear corner modules and mirror-mounted sensors on equipped vehicles. Each has its own procedure, its own tolerance and its own verification step — they are not interchangeable.
Mobile vs In-Shop Calibration in Garland
In-shop calibration at 3002 Edgewood Dr Ste 7 is the right choice whenever the procedure specifies a static target setup: level floor, controlled lighting and exact distance, height and offset from the vehicle's centreline. Those conditions cannot be reproduced reliably on a shop apron or a sloped lot.
Mobile calibration is the right choice for dynamic procedures, scans, electrical diagnostics and module programming that can be completed correctly at your location. We determine which applies from the VIN before the job is booked, so you know up front whether the vehicle travels or we do.
Calibration work we handle in Garland
- Forward camera calibration after a windshield replacement in Garland
- Front radar and blind spot calibration after collision repair
- Calibration required after an alignment, suspension repair or ride-height change
- Camera, radar or sensor replacement that needs initialization and aiming
- Documented pre-repair and post-repair scans for the repair file
More detail on the procedure itself is on our ADAS calibration service page, and related work is covered under electrical and SRS diagnostics and ECU programming.
Garland ADAS calibration questions
- Where is your Garland shop located?
- 3002 Edgewood Dr Ste 7, Garland, TX 75042. Call 214-991-3740 to arrange a drop-off or a mobile visit.
- Can a Garland vehicle be calibrated at my own shop?
- Often yes. Dynamic calibrations, scans, diagnostics and programming can be done at your location. Static procedures that require a level floor and exact target placement are performed in our Garland bay.
- Do you calibrate for Garland glass shops after windshield replacement?
- Yes. Forward camera calibration after glass replacement is a standard part of what we do, following the manufacturer's procedure for that vehicle and documenting the result.
Calibrating a vehicle in Garland?
Call the shop directly or send the VIN and repair details — you'll get scheduling and pricing back, plus whether the vehicle needs in-shop or mobile service.